Brought to you by https://carcomputerexchange.com/jeep/wrangler/cat_11.html
Car Computer Exchange offering 2005 and 2006 Jeep Wrangler PCM parts that are refreshed and reprogrammed with a success rate above industry-standards. Here’s how and why.
Common 2005 and 2006 Jeep Wrangler PCM Problems (and Fixes!)
The powertrain control module (PCM) — sometimes also called an engine computer, ECM, or TCM -- in your Jeep Wrangler acts as the brain of your vehicle’s engine.
More specifically, the PCM in your Jeep is actually a combination of two other computers, the engine control module and the transmission control module. Although it may appear like a single unit from the outside in most vehicles, it is made up of these two separate units which are housed together in a single module.
Think of your Wrangler powertrain control module as a computer similar to a laptop. On the inside it is a combination of circuits and wires that relay and store important data and information. Like the computer you are reading this on, PCM function is determined and controlled by software that allows it to work seamlessly with your particular vehicle.
What Does a PCM Do in a Jeep Wrangler?
Your Jeep Wrangler powertrain computer controls literally hundreds of functions and processes within your Jeep’s engine. This can include everything from controlling when your transmission shifts gears to fuel injection parameters to determining when to activate your check engine light. Needless to say, if your Wrangler’s central computer is not functioning properly, it’s not going to be running properly.
Among other symptoms, signs that your Jeep needs a new PCM include the following:
· Check Engine Light – The light goes on and off and doesn’t seem to correspond to an actual mechanical problem.
· Engine Stalling or Misfiring – Stalling and misfiring may occur without any pattern to frequency or severity.
· Engine Performance Issues – You’ll notice a reduction in fuel efficiency, power, and acceleration.
· Car Not Starting – Your vehicle does not start or is difficult to start. The engine may still crank but won’t be able to start without vital inputs from the computer.
Jeep Wrangler PCMs for 2005-2006
There is a very common issue with control modules in 2005 and 2006 models of the Jeep Wrangler. If you keep your Jeep long enough, you’ll probably encounter a situation where you’ll need to repair or replace your Jeep Wrangler PCM. If you ever notice any of the above signs of a failing Jeep Wrangler PCM, you will want to have the issue checked out to see if the problem is actually the powertrain control module.
When it comes to 2005 and 2006 Jeep Wranglers, there’s a strong chance the PCM is to blame.
TJ Wrangler Model
The TJ Wrangler model produced between 1997 and 2006 was a popular vehicle. It widened the Wrangler’s appeal by offering a smoother ride and more comfort, safety, and entertainment options—features that all add stress to the PCM, just to point out. This model of Jeep Wrangler was so popular that over 965,000 were produced between 1997 and 2006, with over 175,000 2005-2006 TJ Jeep Wranglers being produced.
Put simply, there are a lot of these vehicles on the road, then and now. The problem is, despite being extremely popular, Jeep TJ Wrangler models weren’t without their issues. You can check out any Jeep forum online and see that 2005 and 2006 Wrangler models are notorious for having a host of PCM problems.
From the stalling, misfiring, starting, and performance issues stated above, to issues with engine temperature readings and false engine error codes, the headaches are bad and frequent.
Causes of a Jeep Wrangler PCM Failure
There are a variety of reasons why your Jeep PCM might fail. One the primary ways is because of physical damage. This can be caused by environmental factors like corrosion, thermal stress, vibrations, or if the computer is submerged in water or mud while your tearing off road in your Wrangler. You could also have a voltage overload if there’s a problem with your Jeep’s power supply or wiring, or you might have just gotten unlucky with a poorly manufactured PCM.
However, if the problem with your Jeep Wrangler PCM has no discernible physical cause, there’s a chance it might be an issue with the software.
Reflashing 2005 and 2006 Wrangler PCMs
When you have an issue with or even a failing powertrain control module or engine control module, oftentimes there’s an issue with the software and you have to get it reflashed. Reflashing your Jeep Wrangler PCM is a tuning technique that is also often called flashing, remapping, or flash tuning. Reflashing is not just for bad PCMs, however, you can also reflash your Jeep Wrangler to get the latest software or updates from the manufacturer (OEM).
Like any computer, your car’s PCM or ECM has software with different settings or parameters, and these can be changed to alter the performance and driving limits of a vehicle. Reflashing or remapping an engine computer is essentially just the process of replacing the existing software in a vehicle controller with new software.
The problem with reflashing a 2005 or 2006 Jeep Wrangler, however, is that the post-flash computers have a very high rate of failure once completed, regardless of where you get it reflashed at. Although there are numerous reports of 2005-06 TJ PCM problems (both with the original PCM and software and with difficulty reflashing), there has, unfortunately, never been a recall, legal action, or support from the manufacturer. This has left many Jeep owners without any options.
Fortunately, CarComputerExchange.com can help you with your 2005 – 2006 TJ Jeep Wrangler PCM problems. They’ve developed a thorough, custom process that greatly diminishes the fail rate that many owners experience when they reprogram Jeep computers.